FIRMWARE RELEASE NOTE ===================== Products affected: AXIS C8210 Release date: 2022-05-25 Release type: Production Firmware version: 10.10.73.3 Preceding release: 10.10.73.2 -------------------------------------------------------------------------------- Upgrade instructions ==================== NOTE 1: Firmware image version has been updated in earlier FW version, meaning that upgrade to this release can only be done from FW version 1.97.1 or higher. If your device is currently running a FW version prior to 1.85.06 you need to upgrade in the following steps 1.65.032 -> 1.85.040 -> 1.97.1 or 9.80.3.1 -> 10.x or later FW version NOTE 2: If you need to do a firmware downgrade (and not a rollback) you now need to factory default the device. But you can revert to your previous firmware version and configuration by performing a rollback. NOTE 3: If upgrading a device from 1.65.032 to 1.97, 9.80 or later, without doing a factory default, you will need to change the device settings to allow HTTPS calls. Until done follower devices will stop playing and appear offline to the leader. Upgrade the firmware according to the instructions given at https://help.axis.com/axis-os#how-to-upgrade or howtoupgrade.txt, which is included in the firmware folder. Corrections in 10.10.73.3 since 10.10.73.2 ========================================== 10.10.73.3:C1 Solved a problem where an audio site with connected followers would stop playing, if media encryption was deativated in the System settings menu of AXIS Audio Manager Edge. Corrections in 10.10.73.2 since 10.10.70.1 ========================================== 10.10.73.2:C1 Solved a problem where FW upgrade could fail due to timing issues in larger sites when migrating AXIS Audio Manager Edge configuration and where follower service could crash when not able to reach the leader device. 10.10.73.2:C2 Solved a problem where the status of a follower device erroneous could be shown as stand-alone after upgrade. Features in 10.10.70.1 ======================= AXIS Audio Manager Edge features -------------------------------- 10.10.70.1:F1 Line-in related changes: You no longer need to enable line-in for devices in the physical zones page. In addition full duplex is automatically set on the device if line-in is used as a source. A warning will be given if you configure a device as line-in music source and set the input type in device settings to "Microphone" as this could cause unwanted feedback. FW features ----------------- 10.10.70.1:F2 New primary web user interface for device configuration. The new web interface comes with several features that are new to AXIS Network Audio products, such as: - The device now supports ONVIF backchannel for audio and allows you to create ONVIF users. Please note that the ONVIF standard does not have any standard profile for audio-only devices, and AXIS cannot guarantee the experience in any specific ONVIF application. - Listen and record is available on all AXIS Network Audio products where a microphone is available. This feature allows the user to both listen to and record an audio stream that is captured by the connected microphone, through the web user interface. Please note that the device input must be enabled in Audio --> Device settings. - Set up the device as an MQTT client. MQTT communication is based on two entities, the clients and the broker. The clients can send and receive messages. The broker is responsible for routing messages between clients. You can learn more about MQTT in AXIS OS Portal at https://help.axis.com/axis-os#mqtt - End-users can now configure light profiles with different colors and patterns. These profiles can be used in the feature "Front facing LED to indicate microphone status" Applies to: AXIS C1410 10.10.70.1:F4 Updated to Apache v2.4.53 10.10.70.1:F5 Updated to OpenSSL v1.1.1n Link to AXIS OS Release notes: https://help.axis.com/axis-os-release-notes#axis-os-10-10 Features in 10.8.1.1 ======================= AXIS Audio Manager Edge features -------------------------------- 10.8.1.1:F1 Added support in AXIS Audio Manager Edge for storing multiple background music schedules, named by the user. As before there can only be one active schedule at a time. 10.8.1.1:F2 The status of the SD card is now shown on the AXIS Audio Manager Edge dashboard. FW features ----------------- 10.8.1.1:F3 Added support on AXIS C1410 Network Mini Speaker to indicate microphone status using the front-facing LED. This feature can be controlled from the action engine of the specific device, where three new events are pre-configured and enabled by default: - Front-facing LED Activation: LiveStream - Front-facing LED Activation: Recording (to SD-card or network share) - Front-facing LED Activation: SIP (for this event SIP must be enabled before the LED is activated) Any of these conditions above will turn on the AXIS C1410 Network Mini Speakers LED with green color. The LED activation can be disabled by disabling the pre-configured events. 10.8.1.1:F4 Added two new pre-configured events for a use case where an operator calls the device (via SIP) and a pre-announcement clip is to be played to draw the attention of the person on the receiving end. When the pre-announcement clip has been played, the SIP call should be answered. - Pre-announcement tone: Play tone on incoming call - Pre-announcement tone: Answer call after incoming call-tone Both events require SIP to be enabled. 10.8.1.1:F5 Added support in action engine - "send notification" action to optionally supply: method, HTTP headers and (for applicable method types) a body. This makes it possible to perform REST API calls. 10.8.1.1:F6 Updated Apache to version 2.4.51 Link to AXIS OS Release notes: https://help.axis.com/axis-os-release-notes#axis-os-10-8 Corrections in 10.8.1.1 since 10.6.9.1 ====================================== 10.8.1.1:C1 Fixed an issue where changing day on an advertisement slot did not save it to the correct day. 10.8.1.1:C2 Fixed a FW issue where the device could crash during generation of the server report. Corrections in 10.6.9.1 since 10.6.0.1 ====================================== 10.6.9.1:C1 Fixed a FW upgrade problem that would occur on 1004-E, C2005 or C3003-E products, that were upgraded from 1.65.032 or earlier without ever being factory defaulted. 10.6.9.1:C2 Fixed a problem where AXIS Audio Manager Edge would break if the user deleted one or more duplicated announcement entries related to opening hours. Features in 10.6.0.1 ======================= AXIS Audio Manager Edge features -------------------------------- 10.6.0.1:F1 The sound calibration app in AXIS Audio Manager Edge has been extended with support for normalization. Normalization helps calibrate the sound levels between different sources and devices in the audio site. Please note that if you currently have a gain offset configured for a device, this will be migrated to the output gain configuration. FW features ----------------- 10.6.0.1:F2 Added actions "Play audio clip while active" and "Stop playing audio clip" to the event system for all audio products. 10.6.0.1:F3 Updated OpenSSL from version 1.1.1i to 1.1.1k Link to AXIS OS Release notes: https://www.axis.com/sv-se/products/online-manual/00000#t10168993 Features in 10.4.0.1 ======================= AXIS Audio Manager Edge features -------------------------------- 10.4.0.1:F1 Default Mapping of sources Devices that are not configured as intermediary device for Vapix Audio, Vapix Media Clip or SIP in AXIS Audio Manager Edge, will by default play incoming audio on the device itself. Default mapping of sources will not be enabled by default if upgrading from a previous Edge version but can be enabled manually in AXIS Audio Manager Edge system settings. 10.4.0.1:F2 Latency and sound profiles The calibration app in AXIS Audio Manager Edge now offers the ability to set your desired sound and latency profiles. It supports both default configuration for the site as well as detailed control for specific sources. It supports both default configuration for the site as well as detailed control for specific sources. 10.4.0.1:F3 2 way audio This enables you to setup a half-duplex call to the device. While sound is playing the microphone will be muted to prevent an echo of the speaker’s voice. To enable it you need to enable Echo Cancellation in HW2. You should also turn on full-duplex (to be able to get sound from the microphone), and adjust input gain according to your needs. AAM Edge automatically configure this for you if you use the device as a paging SIP/VAPIX Intercom source. 10.4.0.1:F4 AXIS Audio Manager Edge now supports the Safari browser. 10.4.0.1:F5 New languages in AXIS Audio Manager Edge Japanese, Korean, Russian, Traditional Chinese and Simplified Chinese are added to the list of supported languages [English, French, Italian, Spanish, German, Dutch, Polish, Portuguese (Brazilian)] FW features ----------- 10.4.0.1:F5 Echo cancellation in device configuration web With this feature it is possible to toggle echo cancellation on/off in the device configuration web. Echo cancellation enables microphone gating to avoid echo/feedback loops in half-duplex mode. 10.4.0.1:F6 OAK retrieval in device configuration web Added the possibility to retrieve the device Owner Authentication Key (OAK) in the device web interface. Note that this functionality requires that the product have direct access to the internet. 10.4.0.1:F7 A factory default is now mandatory when trying to downgrade the device. See How to downgrade at https://www.axis.com/support/firmware for more information. 10.4.0.1:F8 Updated Apache to version 2.4.46 10.4.0.1:F9 Updated OpenSSL to version 1.1.1i Link to AXIS OS Release notes: https://www.axis.com/sv-se/products/online-manual/00000#t10166046 Corrections in 10.4.5.1 since 10.4.0.1 ====================================== 10.4.5.1:C01 Fixed potential FW-upgrade problem, that could cause the device to not upgrade correctly and instead keep previous FW-version. Known limitations ================= 10.10.70.1:L1 The pre-configured events for Front-facing LED Activation must be re-started if Light profiles that are used in the event is altered/updated while the event is active. 10.10.70.1:L2 If you have line-in configured as a music source but the device configuration for input set to "Microphone" you will trigger a newly introduced warning in the Axis Audio Manager Edge UI since connecting a microphone to line-in and playing the sound in the site could cause unwanted feedback. 10.8.1.1:L1 From this release and onwards the AXIS Audio Player ACAP is no longer pre-installed. It will need to be manually downloaded and installed to the device. The ACAP can be found here: https://www.axis.com/sv-se/products/axis-audio-player. Please note that if the AXIS Audio Player ACAP was previously installed the ACAP will remain on the devices if FW-upgrade without factory default is performed. 10.8.1.1:L2 There is currently no support for PEM certificates when using TLS authentication in AXIS Audio Manager Edge. 10.4.0.1:L1 When using MS Edge pre-chromium the user is unable to login after setting a password in the device configuration web. 10.0.2.4:L1 To use firmware 10.0.2.4 or higher together with AXIS Audio Manager Pro you must update AXIS Audio Manager Pro to version 3.3.1.3.33 or higher. 10.0.2.4:L2 If the user tries to add more than 40 devices at the same time in AXIS Audio Manager Edge the system might fail to add all devices. The user can still try again and add the remaining devices in one or more sessions. 10.0.2.1:L1 The system will NOT automatically convert the configuration of audio content or schedules from an existing AXIS Audio Player to the new AXIS Audio Manager Edge. This must be done manually. The AXIS Audio Player is still available in this release, and it can be used as normal until the user is ready to perform a manual migration of content and schedules. 10.0.2.1:L2 After the introduction of AXIS Audio Manager Edge, the "System Overview" and "System Settings" options in the device configuration menu may be hidden. If you wish to enable these menu options, please start the AXIS Audio Player ACAP (found under the menu option "Services"). Then open the AXIS Audio Player and use the application (e.g. open the volume slider in the lower right corner and adjust the volume) Go back to the device configuration menu and refresh the browser page. The "System Overview" and the "System Settings" options should now be available. Please note that if you wish to stay with the previous audio system or wish to continue using the Audio relay service API, we strongly advise you to use the long-term support software track (LTS 9.80 track). 10.0.2.1:L3 No support for running AXIS Audio Manager Edge in Internet Explorer. 10.0.2.1:L4 It is currently not possible to create schedules across midnight in AXIS Audio Manager Edge. Schedules can be created from 00:00 to 23:59, but it is not possible to create a schedule from e.g. 21:00 to 03:00 the following day. This use case will have to be schedule with two entries. One entry from 21:00 to 23:59 and a second entry from 00:00 to 03:00 the following day. 10.0.2.1:L5 Uninstalled ACAPs will still show up in the list of available ACAPs when creating an ACAP music source in AXIS Audio Manager Edge. 10.0.2.1:L6 User cannot supply passphrase for encrypted SD cards in the device configuration application after factory default has been performed. 10.0.2.1:L7 When running firmware version 10.0.2.1 or higher the Soundtrack Your Brand ACAP must be updated to version 1.4 or higher.