FIRMWARE RELEASE NOTES
======================

Products affected: AXIS P5512 PTZ Dome Network Camera

Release date:      2011-05-17

Release type:      Production

Firmware version:  5.25

File name:         P5512_5_25.bin

Preceding release: n/a

AMC version:       5.9.9.0-1


------------------------------------------------------------------------------

UPGRADE INSTRUCTIONS
====================

The firmware can be upgraded using Axis Camera Management 3.0, HTTP or FTP.
Please follow the instructions from the user's manual, the web page at
http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named
howtoupgrade.txt.


RELEASE 5.25
============

5.25 is the first official release for the AXIS P5512.

Added features
==============
ImageSource.I0.Sensor.AutoIrCutFilterHysteresis in plain config to
adjust the behaviour of the IR cut filter. 
Valid values 1-15 where:
1 : switch the IR cut filter on early (less light needed)
15: switch the IR cut filter on late (more light needed)


Known limitations
=================
5.25:L01 Audio clip upload size limit, limited to less than ~1.5MB.

5.25:L02 Motion detection reacts to IR cut filter switching.

5.25:L03 Uploading an expired or not yet valid encrypted client certificate in PKCS#12 format for 802.1x will succeed instead of being rejected as it should be

5.25:L04 RTSP clients timeout when syncing unit to computer time due to the keepalive messages being regarded as too old/new depending on the time set.

5.25:L05 Cannot record audio clip with no wait time. You must wait at least 1 second.

5.25:L06 Errors in log when removing micro SD card without unmounting it first.

5.25:L07 Focus can sometimes be somewhat poor on the ELMO 401C block.

5.25:L08 Criticals found in system log at restart when Guard tour is running.

5.25:L09 Control panel hidden behind video sometimes. The AMC component is uncontrollable by the web viewer.

5.25:L10 After a factory the default PTZ home position not defined when the PTZ framework is told to go to the home position; the the camera will remain at the calibration point.

5.25:L11 Onvif failing test case 6.2.24. This is due to a bug in the test tool and test specification, i.e. the Axis interpretation is correct.

5.25:L12 No warning message in log when pre-trigger buffer is too large.

5.25:L13 ONVIF speed param is ignored by the camera.

5.25:L14 MJPG recordings to SD card with too high bitrate may cause oom kill of monolith. Lower the bitrate to a rate the SD card/controller can handle. Cant give specifics since it differs between SD cards.

5.25:L15 From time and duration not respected in continuous recording <5 min; Cue points not available and seeking isnt possible until a MKV-file is finalized (stopped or full 5 minutes).



APPLICATION DEVELOPER Information
=================================

The AXIS VAPIX Application Programming Interface is supported by the AXIS
P5512.

The following groups are supported by the AXIS P5512.
For more information, please refer to the AXIS VAPIX HTTP API specification
version 3, part of the AXIS VAPIX API, available at www.axis.com.

Group             Exceptions
=====             ==========
General
Image and Video
PTZ               PTZ driver update (ptzupdate.cgi), PTZ administration
                  (ptzadmin.cgi), set PTZ parameters (ptzparam.cgi)
Motion Detection
I/O
IP filter
Audio

Built in templates for dynamic parameters are:

Template              Group
========              =====
'event'               Event
'audioclipaction'     Event.E#.Actions
'ftpaction'           Event.E#.Actions
'guardtouraction'     Event.E#.Actions
'httpaction'          Event.E#.Actions
'hwaction'            Event.E#.Actions
'ptzaction'           Event.E#.Actions
'ptzsensoraction'     Event.E#.Actions
'recordaction'        Event.E#.Actions
'smtpaction'          Event.E#.Actions
'tcpaction'           Event.E#.Actions
'ftp_config'          EventServers.FTP
'http_config'         EventServers.HTTP
'tcp_config'          Eventservers.TCP
'guardtour'           GuardTour
'tour'                GuardTour.G#.Tour
'mediaclip'	      MediaClip
'motion'	      Motion
'button'              PTZ.Auxiliary.A1.Button
'ptzlocator'          PTZ.Locator.L#.Zone
'position'            PTZ.Preset.P0.Position
'user_ctlqueue'       PTZ.UserCtlQueue
'streamprofile'       StreamProfile
'streamcache'         StreamCache

Supported AXIS VAPIX API Image Resolutions for AXIS P5512


Resolution  Exceptions
==========  ==========
4CIF
704x576     1)
704x480        2)
2CIF
704x288     1)
704x240        2)
CIF
352x288     1)
352x240        2)
QCIF
176x144     1)
176x120        2)

1) Only available for 50Hz cameras
2) Only available for 60Hz cameras

90/270 degress rotation is not supported.